Automotive glass products, Parts, Glazing, Tools & Equipment   

	Home » GLAZING » KNIVES AND BLADES   1" UltraWiz Cold Knife Blades - 10 PN1002 has a 1" long cutting area. This is the most popular blade because on most vehicles it will cut the urethane with one cut. Original Thickness. Package of ten. Price: $28.00 1" UltraWiz Cold Knife UltraThin Blades - 10 PN5002 is a 1" UltraThin cold knife blade and the most common size used by technicians. They are 40% thinner than the regular UltraWiz blades. Package of ten. Price: $37.00 1/2" SuperScraper Blades - 5 Replacement SuperScraper and PrepMaster Blades made of surgically sharp, stainless steel. Also available in two additional widths: 5/8", and 3/4". Package of five. Price: $3.00 1-1/2" UltraWiz Cold Knife Blades - 10 PN1004 has a cutting area that is 1-1/2" long. We do not recommend using this blade for initial cuts. Use a shorter blade to make your first cut, then go back with this blade to make your final cut. Especially useful where urethane is very wide, such as corners and along the bottom. Original Thickness. Package of ten. Price: $40.00 1-1/2" UltraWiz Cold Knife UltraThin Blades - 10 PN5004 is a 1-1/2" blade and should never be used for the first cut. Always use a shorter blade to make the first cut then finish cutting through the urethane with this long blade. Package of ten. Price: $50.00 1-1/4" UltraWiz Cold Knife Blades - 10 PN1003 1-1/4" original thickness blades are designed with an extra space between the blade and the pull handle bolt. This extra space gives you greater clearance when the glass has a bonded molding. Original Thickness. Package of ten. Price: $40.00 1-1/4" UltraWiz Cold Knife UltraThin Blades - 10 PN5003 is a 1 1/4" UltraThin cold knife blade. They are 40% thinner than the regular UltraWiz blades. Package of ten. Price: $47.00 14" PipeKnife With Neoprene Cover BD79 The PipeKnife is 14" long and has a 6-1/2" flattened blade shaft with rounded corners. The PipeKnife is made of cast aluminum but has a steel nut cast into the back side to receive the screw and prevent stripping of the threads. Take out the rear plug and you can put a pipe in the handle to extend its length. The PipeKnife can use all standard utility knife blades including our ULB582 and DD1086 Extra-Long Utility Knife Blades. Blades not included. Price: $23.00 18" PipeKnife With Neoprene Cover BD79XL The PipeKnife XL has is a slot cast into the end of the handle that lets you store extra blades. The PipeKnife XL is made of cast aluminum, is 18" long and has a flattened blade shaft that is 8-1/2" with rounded corners. It has a steel nut cast into the aluminum for the blade clamp screw. The PipeKnife XL can use all standard utility knife blades including our ULB582 and DD1086 Extra-Long Utility Knife Blades. Blades not included. Price: $35.00 3/4" SuperScraper Blades - 5 Replacement 5/8" SuperScraper blades. They are made of surgically sharp stainless steel. Also available in 1/2" and 5/8" wide. Package of five. Price: $3.00 3/4" UltraWiz Cold Knife Blades - 10 PN1001 has a cutting area that is 3/4" long. It is commonly used to cut standard-width urethane. Many technicians use this blade to make the first cut when cutting wide urethane. Original Thickness. Package of ten. Price: $28.00 3/4" UltraWiz Cold Knife UltraThin Blades - 10 PN5001 is a 3/4" UltraThin cold knife blade. They are 40% thinner than the regular UltraWiz blades. Package of ten. Price: $37.00 3/8" UltraWiz Cold Knife Blades - 10 PN1000 is intended for use as a starter blade. The cutting area is 3/8" long and is useful when starting your first cut on urethane that is wider than a regular blade. Original Thickness. Package of ten. Price: $28.00 5/8" SuperScraper Blades - 5 Replacement 5/8" SuperScraper blades. They are made of surgically sharp stainless steel. Also available in 1/2" and 3/4" wide. Package of five. Price: $3.00 Bent Putty Knife 1 1/4'' Bent carbon steel blade, putty knife Price: $8.50 Blade ULB-582 Extra Long Utility Blades Price: $9.95 Breakaway Blades for Olfa LB21 fits the Olfa XL2, Olfa OLF20, Olfa Silver (SVE802), and Olfa OH1. They will also fit all standard breakaway point knives. When the point of the LB21 breaks or dulls, simply snap off the segments and you have a new, sharp cutting tip. It is very useful for cutting urethane that is far below the dash of most automobiles. Package of ten. Price: $10.00 Breakaway Blades for Olfa Silver - 10 Stainless Steel blades for the Olfa Silver Knife (SVE802). Package of ten. Price: $9.00 Breakaway Point Blades - 5 Breakaway point blades for OH1 knife. Package of 5. Price: $10.00 Chisel Edge Putty Knife 1 1/4'' Chisel edge carbon steel blade, putty knife Price: $7.40 1 of 3 Express Blade Sharpener SFE329 Retain the chisel edge on your Express Blades! To get the best performance, it is important to put a good edge on the blade every time you use your auto glass cut-out knife. Since you do not always have access to a bench grinder, this sharpener will do that quick touch up that brings the blade back to a razor-sharp edge. You can sharpen the blade in about 10 seconds by dragging the sharpener across the blade 3 or 4 times. All off-the-shelf sharpeners will put a V-type edge on the blade and this type of sharpening can prevent the tool from working properly. Our Express Blade Sharpener puts the chisel-type edge on the blade and keeps your auto glass cut-out knife operating at peak performance. It also features a built-in protector to keep you from cutting your hand on the blade. Price: $19.00 Extra Long Utility Knife Blades - 10 Standard utility knife blades measure only 2-3/8" long. The maximum cutting area you can get is approximately 1". Equalizer extra-long utility knife blades measure a big 3-3/4" long and give you an exposed cutting area of, at least, 2-1/4". They are designed so there is more length between the two notches. For this reason, these blades will fit most standard utility knives as well as all long knives that use the standard utility knife blade. Package of ten. Price: $8.00 Extractor Delta Blade 10" EXT-DELTA-XXXL Most Extractor blades are now made from stainless steel, and have been cut and tapered to our exacting, custom specifications. The blades offer excellent flexibility and strength. If used correctly, they should last 200 cut-outs or more. Many users report 300 - 400 cut-outs. For best results it is necessary to keep the blade sharp and use adequate water for lubrication. The blades are very easy to sharpen. Simply run across a wet belt sander, grinder or file, putting a 45 degree edge on one side of the blade, in the same manner as you would sharpen a chisel. Price: $40.00 Extractor Delta Blade 6 3/4" EXT-DELTA-L Most Extractor blades are now made from stainless steel, and have been cut and tapered to our exacting, custom specifications. The blades offer excellent flexibility and strength. If used correctly, they should last 200 cut-outs or more. Many users report 300 - 400 cut-outs. For best results it is necessary to keep the blade sharp and use adequate water for lubrication. The blades are very easy to sharpen. Simply run across a wet belt sander, grinder or file, putting a 45 degree edge on one side of the blade, in the same manner as you would sharpen a chisel. Price: $28.50 « Previous | 1 | 2 | 3 | Next »
	home | products | about us | search | links |checkout | contact us Copyright Policy  Privacy Policy Copyright © 2021 Western Glass Supply Inc, All rights reserved. Design and Hosting by SanbornWebDesigns